Glen Chimney Service in Hyderabad
Repair, deep cleaning and installation for every Glen kitchen chimney — the filterless 6000-series auto-clean hoods, BLDC inverter models and older baffle hoods alike — at your home across Hyderabad and Secunderabad.
We are an independent appliance repair business servicing Glen kitchen chimneys at home in Hyderabad. We handle deep cleaning, BLDC and induction motor faults, auto-clean and oil-collector problems, touch and motion-sensor panels, and new installation. We are not an authorised Glen service centre, so for an in-warranty motor claim you are usually better off going to Glen directly — and we will tell you when that is the case.
- Brand
- Glen Appliances, started January 1999, manufacturing at IMT Faridabad, Haryana
- Hood types serviced
- Filterless auto-clean, BLDC inverter and older baffle-filter models
- Sizes
- 60, 75, 76 and 90 cm, wall mounted
- Suction range
- Roughly 1,000 to 1,400 m³/hr across the range
- Glen published warranty
- On the 6069 BL BLDC, 12 months on the product and 7 years on the motor
- Speeds
- Up to 9 on BLDC inverter models, about 1,000 to 2,500 RPM
- Languages
- English, Hindi, Telugu
What we service on a Glen chimney
- Deep cleaning of the inner cone, impeller, motor housing, oil channel and detachable collector
- BLDC and inverter board diagnosis before any motor is condemned
- Auto-clean and auto oil-collection faults, including a collector that no longer seats
- Touch panel and motion sensor repair, including sensors triggering on steam
- Older induction motors: bearings, capacitors and rewinding
- LED lamps and drivers, curved-glass refitting, corroded GPSP body panels
- Installation, re-siting during a kitchen change and duct re-routing
Related: chimney cleaning, chimney repair and chimney installation.
Why Glen reaches us sooner
Glen’s published product warranty on its BLDC chimneys is twelve months, considerably shorter than the five years Faber and Elica publish on much of their range. The motor is covered far longer, at seven years on the 6069 BL BLDC.
In practice that means a Glen hood leaves its product warranty after a single year, so panels, boards, sensors, lamps and oil-related faults fall to an independent technician almost immediately. The motor stays the exception worth claiming.
Common Glen chimney problems
These are the Glen complaints we attend to most often in Hyderabad. A symptom usually points to one likely cause, but we confirm it on site before quoting.
| Symptom | Most likely cause | What we do | Typical time |
|---|---|---|---|
| Suction dropped off over a year or two | Inner cone and impeller coated in hardened oil; emptying the collector does not touch them | Strip the hood, degrease the cone and impeller, flush the oil channel and duct mouth | 70–100 min |
| Oil overflowing from the collector | Collector not seated after a previous clean, or the oil channel is choked upstream | Reseat the collector, flush the channel, replace a hardened gasket | 40–70 min |
| Hood dead, no fan and no lights | Power supply or inverter board on a BLDC model; a capacitor on older induction models | Test the supply and board first; replace the motor only if it has actually failed | 60–120 min |
| Speed stuck or will not go past one setting | Inverter board fault on BLDC models, or a failed switch on push-button hoods | Test and replace the board or switch, then check RPM across all speeds | 50–90 min |
| Rattling or droning noise | Impeller unbalanced by uneven oil, or a worn bearing in an older induction motor | Clean and re-balance the impeller, replace the bearing and re-grease the shaft | 60–120 min |
| Touch panel unresponsive | Oil ingress behind the glass onto the control board | Clean the panel and board, repair the track, or replace the panel | 45–90 min |
| Smoke escaping at the sides | Hood too high above the hob, or a 1,200 m³/hr hood in a kitchen that needs more | Correct the height and shorten the duct; if the hood is undersized we say so plainly | 90–180 min |
Times are for one technician at your home and exclude waiting for a spare part that has to be ordered.
Glen chimney models we service
All Glen chimneys, current and discontinued, including the 6000-series models below. Figures are as published by Glen and its Indian retailers; your unit’s exact specification is on the rating sticker inside the hood.
| Model | Width | Suction | Filter and cleaning | Controls |
|---|---|---|---|---|
| Glen 6069 BL BLDC | 76 and 90 cm | 1400 m³/hr | Filterless, auto clean with oil collection | Touch and motion sensor, 9 speeds |
| Glen 6053 BL BLDC | 76 cm | 1400 m³/hr | Filterless, auto clean | Touch control panel |
| Glen GL 6073 BL ACLN MS | 75 and 90 cm | 1400 m³/hr | Filterless, auto clean | Touch and motion sensor |
| Glen GL 6074 BL ACLN MS | 75 cm | 1400 m³/hr | Filterless, auto clean | Touch and motion sensor |
| Glen CH 6074 AC 90 | 90 cm | 1400 m³/hr | Auto clean | Motion sensor |
| Glen 6059 BL | 90 cm | 1200 m³/hr | Filterless, auto clean | Touch control panel |
| Glen 6062 BL | 60 cm | 1200 m³/hr | Filterless, auto clean | Touch control panel |
| Glen 6070 JU BL | 60 cm | 1000 m³/hr | Baffle filter, curved glass | Push button |
Models not listed here are still serviced. Call us with the number on your sticker.
How to read your Glen model number
Glen names are mostly a series number plus a few suffixes, and reading them tells us the motor type and cleaning system before the visit. Glen publishes no official key, so the entries below are read from Glen’s own listings and Indian retail spec sheets.
| Code | What it means | Why it matters for a repair |
|---|---|---|
| 60xx | The series number: 6053, 6059, 6062, 6069, 6070, 6073, 6074 | Identifies the body, glass and bracket, and which impeller fits |
| 60 / 75 / 76 / 90 | Width of the hood in centimetres | Decides the canopy and mounting hardware we carry |
| BL | Black finish | Matters only for replacement glass and trim panels |
| BLDC | Brushless DC motor with inverter control, confirmed on the 6053 and 6069 | A dead hood is usually the inverter board, not the motor |
| ACLN / AC | Auto Clean | Means a heating or oil-release system that can fail while the fan runs fine |
| MS | Motion Sensor control | A hood starting or changing speed on its own is usually this sensor |
| JU | Appears on older Glen curved-glass baffle hoods | Expect baffle filters and push-button switchgear, not a control board |
| GPSP | Not a model code — the galvanised painted steel Glen uses for the body | Corrodes if oil is left standing, so it is worth checking during a deep clean |
Where to find it: on the rating sticker inside the hood, usually under the canopy or at the back near the duct outlet. It reads as a long string such as CH6069DCACBL76.
Glen’s warranty, and what it covers
Glen’s published cover on its BLDC chimneys is twelve months on the product and seven years on the motor, as listed for the Glen 6069 BL BLDC. That product warranty is considerably shorter than the five years Faber and Elica publish on much of their range.
If your Glen is under a year old, the whole unit is likely still covered and you should go to Glen first. If it is older but under seven years and the motor itself has failed, the motor should still be a Glen claim.
Cover differs by model and by the dealer you bought from, so check your own invoice before assuming these figures apply to your hood.
What we handle instead
Everything else: deep cleaning, oil and collector faults, inverter boards, touch panels and sensors, duct problems, installation and re-siting, lamps and physical damage.
On BLDC models it is worth letting us test the inverter board before anyone replaces a motor. In our experience the board fails first, and that is the much smaller repair.
Sources: Glen India product listings and Indian retailer specification sheets.
How a Glen service visit works
- You send the symptom. Call or send a short video of the chimney running. Sound and smoke tell us more than a description, and it lets us carry the right spare on the first visit.
- We tell you what it is likely to be. You get a probable cause and a price range before anyone travels, along with the visit charge.
- On-site diagnosis. The technician opens the hood, checks suction at the canopy, tests the inverter board on BLDC models, inspects the duct and flap, then shows you the fault before quoting.
- Repair or deep clean. Work is done at your home. Floors and the hob are covered, oil-soaked parts are degreased in a tray, and old parts are handed to you.
- Test and hand over. We run every speed, check noise and suction with the kitchen door shut, clean the work area and give you a dated bill.
Full detail on charges is on the service charges page, and the areas we cover are listed under service areas.
Glen chimney questions
How long is the Glen chimney warranty?
Glen’s listed cover on its BLDC chimneys, such as the 6069 BL BLDC, is twelve months on the product and seven years on the motor. The one-year product warranty is much shorter than Faber’s or Elica’s five years, which is why most Glen repairs reach independent technicians quickly. Check your own invoice, since cover varies by model.
My Glen chimney is dead. Do I need a new motor?
Probably not. On Glen’s BLDC models the motor is driven by an inverter board, and that board fails more often than the motor does. We test it first, which frequently turns a motor replacement into a much smaller board repair.
The oil collector keeps overflowing. What is wrong?
Either the collector is not seating properly, which is common after it has been removed and refitted a few times or once heat has warped the lip, or the oil channel upstream is choked so oil backs up and spills elsewhere. We clear the channel, reseat or replace the collector and check the gasket.
Does Glen’s auto clean mean I never need a deep clean?
No. Auto clean and auto oil collection move oil towards the collector; they do not clean the inner cone, the impeller blades, the motor housing or the duct. Those surfaces coat up regardless and are the usual reason a two-year-old Glen pulls weakly. A hand strip-down every four to six months keeps the suction where it started.
Do you service older Glen baffle-filter chimneys?
Yes. Older Glen hoods such as the 6070 JU BL use stainless baffle filters, push-button switchgear and a plain induction motor. They are simpler to repair than the current BLDC models, parts are still available, and a well-maintained one will outlast a neglected new hood.
Why does my Glen chimney start on its own?
Models with MS in the name have a motion sensor, and an oily sensor lens or a rising plume of steam can read as a hand passing in front of it. Cleaning and re-calibrating the lens fixes most cases; a failed sensor module is a quick swap.
Do you fit genuine Glen spare parts?
We use genuine Glen parts where they are available to independent dealers, and OEM-grade equivalents where Glen supplies only through its own network. We tell you which one is going in before we fit it and hand you the old part afterwards.
Which areas do you cover for Glen service?
Hyderabad and Secunderabad, including Kukatpally, Nizampet, Bachupally, Miyapur, Madhapur, Kondapur, Gachibowli, Manikonda, Banjara Hills, Jubilee Hills, Mehdipatnam, Attapur, Uppal and LB Nagar. The full list is on the service areas page.
Independent service notice. AS Chimney Services Hyderabad is an independent appliance repair business. We are not an authorised service centre of Glen and we are not affiliated with or endorsed by Glen Appliances. The name Glen and its logo are trademarks of their owner, used here only to describe the appliances we repair. For in-warranty claims, contact Glen directly.